Solution Summary: Motorized Concrete Screeds
A motorized screed consists of a blade, or plow, that floats on and vibrates the concrete during screeding operations.
Description:
Use a motorized screed (also called a vibratory screed). You can work standing upright, and operating the screed takes much less effort than hand screeding.
This type of screed eliminates both screeding in a stooped position and the need for repeated arm and shoulder movements.
(Photo courtesy of NIOSH)
The motorized screed consists of a blade or plow that floats on the concrete, one or two gasoline motors that vibrate the blade, metal support tubing, and handles for the operator.
Risks Addressed:
When you hand screed concrete, you work bent over, and you have to use a strong grip to pull the board over the wet concrete. Your arms and shoulders exert a lot of force over and over.
Doing this work often or for a long period of time increases your chance of fatigue and pain. It puts major stresses on your back, knees, hands, arms, and shoulders, which may lead to serious muscle or joint injuries.
How Risks are Reduced:
A motorized screed should reduce a worker's chance of developing muscle and joint injuries.
This equipment greatly reduces the physical effort needed for hand screeding, and eliminates the frequent and prolonged stooping. Little effort is needed to move the plow over the concrete surface. This type of screed eliminates both screeding in a stooped position and the need for repeated arm and shoulder movements.
Biomechanical research shows that high compression forces occur in the spine while stooping, and that sustained or repeated flexion of the spine may decrease the stability of the lower back and increase the risk of fatigue, leaving the back more vulnerable to injury.
While there is considerable research shows that working in stooped, kneeling and squatting postures causes low back disorders, the research mostly focuses on those postures in combination with other risk factors such as bending or twisting or heavy loads. The literature combining stooped, squatting or kneeling postures with load handling shows rapid and severe spinal damage. There is much less in the literature regarding the health effects of these postures in an unloaded situation - that is, stooping without lifting.
However, safety and health experts believe that it is important to avoid prolonged and repeat forward bending of the back (stooping) even in the absence of the other risk factors for low back disorders.
Effects on Productivity:
Screeding with motorized equipment can be faster than hand screeding. Many contractors report improvements in productivity. The vibration of the blade improves the consolidation of the concrete and reduces time spent "bull floating" the surface.
Additional Considerations:
There are some drawbacks. Although you can work around electrical or plumbing stubs, some hand screeding may still be necessary. Also, it can be difficult to move the screed to and from the work location. A single-engine screed weighs around 50 lbs., and can be awkward to lift and carry. Some screeds have a quick-release system to remove the plow from the frame, which makes carrying easier.
Vibration can also be a problem. It is important to protect workers from hand-arm vibration syndrome (HAVS), a nerve disorder that can become disabling. NIOSH measured vibration levels on three types of motorized screeds. Two had the gasoline engine placed at the bottom of the frame and above the plow. One screed had the engine placed on a single shaft, and the operator held the shaft below the engine. Vibration levels for the two types with the engine at the bottom were below the current recommended guidelines to prevent HAVS. The third screed, which was also older and poorly maintained, gave off much higher vibration that could exceed current HAVS guidelines. Higher vibration levels are expected when the engine is connected to the frame or shaft that the operator must grip. When buying a motorized screed, ask about vibration levels and test drive the screed.
Availability
Allen Engineering Corp.
To obtain information, visit www.alleneng.com
or contact 1-800-643-0095 customerservice@alleneng.com
MultiVibe
To obtain information, visit www.multivibe.com
or contact 1-270-554-2615 sales@multivibe.com
MBW Inc.
To obtain information, visit www.mbw.com
or contact 1-800-678-5237 sales@mbw.com
